Tubo com aletas longitudinais

Datang’s Welded Tubos com aletas longitudinais are produced by resistance welding fins in the longitudinal direction along the length of the tube. The fin strip is first formed into a U-shaped channel, such that each leg of the U will form a fin. The channels are cut to the appropriate length and then oriented along the length of the tube and resistance welded in place. The channels are welded in pairs, diametrically opposed — therefore the number of fins specified must always be a multiple of four.

For a given pipe or tube size, the desired heat transfer surface area per unit length of tube can be obtained by specifying the appropriate fin height and number of fins. The maximum number of fins is dependent upon the tube outside diameter — larger OD tube can accommodate a greater number of fins. See Design Information for extensive tables of surface areas and fin weights.

Some customers specify that the longitudinal finned tubes be “Cut and Twisted.” This operation consists of cutting through the fin channels circumferentially at specified intervals along the tube length. The fins are then bent (or “twisted”) on one side of each cut, creating a discontinuity that promotes turbulent fluid flow, thereby enhancing heat transfer efficiency.

The following table shows Datang’s manufacturing capabilities for longitudinal finned tube:

* This table should be used as a general guide to our capabilities for Welded Longitudinal Finned Tubes. Grade of material, tube outside diameter to fin height and other factors may limit these capabilities. Please call us for guidance when designing your next finned tube.

Longitudinal Finned Tube for Heat Exchanger

Datang longitudinal finned tube heat exchanger is an important heating equipment. It has important practical significance for energy saving and emission reduction, improving the thermal efficiency of fin tubes, reducing exhaust gas temperature, and improving the safety and stability of fin tube radiators.

What is Longitudinal Finned Tube?

The longitudinal finned tube heat exchanger can significantly improve the heat transfer, and its heat transfer effect is obviously better than that of the flat sheet high-frequency welded finned tube radiator.

The thermal conductivity of the corrugated high-frequency welded finned tube radiator is The flat sheet high-frequency welded finned tube radiator is about 2.2 times, but the radiators of the two structures have their own advantages and disadvantages, and people should choose carefully according to actual needs. If the heat transfer coefficients on both sides of the tube of the high-frequency welded finned tube radiator are very different, fins should be installed on the side with the smaller heat transfer coefficient.

For example: boiler economizer, water flows in the tube, flue gas flows out of the tube, and fins should be used on the flue gas side;

air cooler, liquid flows in the tube, air flows out of the tube, and fins should be added on the air side;

steam generator, the tube is When the water boils, the flue gas goes out of the pipe, and the fins should be added on the flue gas side.

It should be noted that in the design, the side with the small heat transfer coefficient should be placed outside the tube as much as possible to facilitate the installation of fins.

Like welded helical finned tubes, this welded configuration can be used for practically any heat transfer application, and is particularly suited to high temperature, high pressure applications with high fin-side temperatures.

The choice of longitudinal finned tubes versus helical finned tubes seems to be governed mainly by geometric considerations. For example, some heater configurations consist of finned tubes inserted inside other tubes — longitudinal finned tubes are the obvious choice for such applications.

In other cases, users prefer tubos com aletas longitudinais for installations where the tube will be oriented in a vertical direction — the fin orientation facilitates fluid drainage on the fin side of the tube.

The longitudinal fin configuration is most commonly used in shell and tube type applications such as in double-pipe and multi-pipe heat exchangers where the longitudinal finned tube is telescoped inside the bore of a larger tube shell. Heat is transferred between the fluid passing through the bore of the finned tube and the fluid passing through the bore of the shell. Fluids passing through the bore of the shell are forced between the longitudinal fins. In this case, a helical fin would block the flow of the fluid, rather than allowing the fluid to run between the fins.

To learn more about this product see Datang’s Standard Specifications for Welded Longitudinal Finned Tubes.